 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| IS1604 IS1604 s Features 1. OPIC light detector for RF signal detection (6-division PIN and amplifier IC integrated onto single chip) 2. High speed response type (response frequency : MIN. 8MHz) 3. Compact and thin package (Package dimension : 5.0 x 4.0 x 1.5 mm) 4. Customer-compatible light detector pattern *PINPD : PIN type photodiode OPIC Light Detector for 4 times Speed CD-ROM Drive s Outline Dimensions 10 9 8 7 6 0.5 0.4 (Unit : mm) 2.0 (2.2) 8.4 P=0.8 12345 5.0 5.0 Terminal configuration 4.0 0.15 1 2 3 4 5 VD VA NC VB Vc 6 7 8 9 10 VE GND Vs Vcc VF Internal block diagram R1 Vcc - 1.5 A B C D E F VS VS VS VS VS VS + VA s Applications 1. CD-ROM drive (4 times speed) R1 + Vs GND VB R1 + VC R1 + VD R2 + VE R2 + VF Shape of detector portion Y 190 105 105 150 150 190 (Unit : m) s Absolute Maximum Ratings Parameter Supply voltage *1 Output voltage Operating temperature Storage temperature *2 Soldering temperature Symbol VCC Vo Topr Tstg Tsol Rating 9 VCC - 20 to + 80 - 40 to + 85 260 F (Ta=25C) Unit V C C C C E X 6 X' DC AB Y' *1 To apply to individual terminals of VA to V F . *2 For MAX. 3 seconds at the position of 1.0 mm from the resin edge * OPIC (Optional IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signal-processing circuit integrated onto a single chip. " In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device." 250 IS1604 s Recommended Operating Conditions Parameter Operating supply voltage range 1 Operating supply voltage range 2 *3 Incident light quantity range 1 *4 Incident light quantity range 2 *3 To apply to individual detectors of A,B, C and D. *4 To apply to individual detectors of E and F. Symbol Vcc Vs P1 P2 MIN. 4.5 Vcc/2 - TYP. 5 Vcc/2 6 6 MAX. 5.5 Vcc/2 10 10 Unit V V W W s Electro-optical Characteristics Parameter Supply current Output offset voltage Symbol I CC Vod Vod Conditions Specified in pressure difference from Vs A-B C-D (A+ C)- (B+ D) E- F *5 ( Ta = 25C,V CC = 5V, Vs = 2.5V ) Output offset voltage differenc Sensitivity 1 *5 Sensitivity 2 *5 Sensitivity ratio *5 Sensitivity temperature coefficient Response frequency 1 Response frequency 2 Output noise level Rp1 Rp2 Rp2/Rp1 Rpt fC1 fC2 Vn Ta=- 20to+ 80C -3dB,CL = 30pF - 3dB,CL = 30pF f= 2.9MHz,BW= 10kHz MIN. 0.6 - 15 - 15 - 15 - 15 - 15 18 32 1.6 8 1 - TYP. 1.5 0 0 0 0 0 33 58 1.9 4 000 11 1.5 - 76 MAX. 4 + 15 + 15 + 15 + 15 + 15 53 93 2.2 - 64 Application VCC VAto VF VA,VB VC,VD mV VAto VD VE,VF VAto VD mV/ W VE,VF mV/ W VAto VF VAto VF ppm/ C VAto VD MHz VE,VF MHz VAto VF dBm Unit mA mV *5 5 W DC light ( =780 nm laser diode) is radiated to vicinity of the center of each detector at 30 . Assuming the then output voltage as Vp and the dark output voltage as Vod, sensitivity Rp is defined according to the following formula. Rp = ( Vp-Vod ) /5 m W Fig. 1 Response Frequency vs. Supply voltage 20 Fig. 2 Response Frequency vs. Ambient Temperature 20 Response frequency f C1,fC2 ( MHz ) Response frequency f C1,fC2 ( MHz ) RL = 10k Ta = 25C 15 VCC = 5V RL = 10k 15 10 10 5 5 0 2 4 6 8 10 0 - 40 0 40 80 120 Supply voltage VCC (V) Ambient temperature Ta (C) q Please refer to the chapter "Precautions for Use". (Page 78 to 93) |
Price & Availability of IS1604
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |